Sheet Metal Workers in the Atlantic City area earn a median of $100,470 a year, 63% above the typical U.S. metro. That ranks #5 of 273 metros for sheet metal worker salaries across the U.S..
Within driving distance, the same work pays less in Dover.
It's the only New Jersey metro with published pay for this trade; see sheet metal worker pay in New Jersey, including rural areas.
Sheet Metal Worker pay in Atlantic City at a glance
- Sheet metal workers in the Atlantic City, NJ metro earn a median $100,470 a year ($48.30 an hour), #5 of 273 U.S. metros (BLS, May 2025).
- The middle 80% earn between $47,020 and $124,200.
- After local prices, that median buys what $101,632 would in a typical U.S. place (BEA, 2024).
- A typical 1-bedroom rents for $1,555 a month, 19% of the median pay (HUD, FY2027).
Check your pay here
Enter a rate to see where it falls among sheet metal workers in Atlantic City.
Comparing two real offers with overtime and commutes? Use the job offer checker.
What this means Our calculation
Pay for sheet metal workers here is in the top 20% of U.S. metros, and also in the top 20% once local prices are factored in. For the wider job market, unemployment is higher than in most metros (7.3%) and the population is growing slowly (+0.8% since 2020).
Atlantic City scorecard for sheet metal workers Our calculation
Grades compare Atlantic City with every other U.S. metro for this trade (A = top 20%).
Pay Government data
Pay range
Shaded: the middle half of workers. Grey line: typical U.S. metro ($61,460).
Pay over time
The median pay for sheet metal workers in the Atlantic City area went from $45,740 in 2022 to $100,470 in 2025, up 119.7%. Prices rose 10% over the same period, so after inflation that's +99.7% — a real raise. Some years are missing because BLS redrew or didn't publish this metro.
BLS OEWS, May 2022–May 2025; inflation: CPI-U (May to May). Year-to-year changes can include survey noise.
Compared with nearby metros
What the pay is really worth in Atlantic City Our calculation
Prices in the Atlantic City area run 1% below the U.S. average. Adjusted for that, a median paycheck here buys what $101,632 would in a typical place, ranking #2 of 272 on real pay.
Real pay or rent burden?
Real pay already accounts for housing, because the price index includes rent. Rent burden shows what share of pay a typical 1-bedroom takes. Use either one, not both together.
Want the full picture? Build a Atlantic City budget on this pay from this pay, local rent and prices.
What sheet metal workers do
Fabricate, assemble, install, and repair sheet metal products and equipment, such as ducts, control boxes, drainpipes, and furnace casings. Work may involve any of the following: setting up and operating fabricating machines to cut, bend, and straighten sheet metal; shaping metal over anvils, blocks, or forms using hammer; operating soldering and welding equipment to join sheet metal parts; or inspecting, assembling, and smoothing seams and joints of burred surfaces. Includes sheet metal duct installers who install prefabricated sheet metal ducts used for heating, air conditioning, or other purposes.
Most important day-to-day tasks
- Maintain equipment, making repairs or modifications when necessary.
- Fabricate ducts for high efficiency heating, ventilating, and air conditioning (HVAC) systems to maximize efficiency of systems.
- Fasten seams or joints together with welds, bolts, cement, rivets, solder, caulks, metal drive clips, or bonds to assemble components into products or to repair sheet metal items.
- Transport prefabricated parts to construction sites for assembly and installation.
- Install assemblies, such as flashing, pipes, tubes, heating and air conditioning ducts, furnace casings, rain gutters, or downspouts in supportive frameworks.
Outlook & getting started
Nationally, sheet metal worker jobs are projected to grow 2.5% from 2025 to 2035 (all jobs: 3.5%), with about 9,800 openings a year. About 8% are self-employed.
What the work is like Government data
How often sheet metal workers deal with each condition, from surveys of workers in the job.
Getting started usually takes some preparation (high school plus months of training).
O*NET 31.0 Work Context and Job Zones (U.S. Department of Labor), national.
Getting started: registered apprenticeship Government data
Most sheet metal workers train through a paid apprenticeship: you work and earn under experienced pros while taking classes, and pay usually rises as you progress. 727,586 people were active registered apprentices nationwide in FY2026, up 87% since FY2016, and construction is the largest field with 290,043 of them (40%), according to the U.S. Department of Labor.
Search apprenticeship openings near Atlantic City ↗Find training programs & sponsors ↗
Official U.S. Department of Labor tools at Apprenticeship.gov. Counts: DOL Apprentices by State dashboard, FY2026 (all occupations).
Licensing in New Jersey Official source
The main state licensing office in New Jersey is the New Jersey Division of Consumer Affairs. It can point you to the right license for sheet metal workers.
Official New Jersey licensing site ↗
Requirements for sheet metal workers vary by state and sometimes by city; always confirm with the official agency.
On-the-job safety Government data
Nationally, sheet metal workers have 163 injuries or illnesses serious enough to miss work per 10,000 full-time workers, 1.9× the rate for all jobs (87). The most common cause is falls, slips and trips.
BLS Survey of Occupational Injuries and Illnesses, 2023–2024 (national, cases with days away from work).
How much work is there? Government data
Local job market
The Atlantic City area's unemployment rate was 7.3% in 2025 (all workers, not just sheet metal workers), above the typical U.S. metro's 4.1%. It was 9.4% in 2021.
BLS Local Area Unemployment Statistics, annual averages 2021–2025 (2025 preliminary).
Getting to work
The average commute in the Atlantic City area is 26 minutes each way, longer than the typical metro (24 min). 13% of commuters spend 45 minutes or more. 76% drive alone, 3% take transit and 9% work from home (all workers, not just trades).
Census American Community Survey, 2024 1-year estimates (table S0801).
Population
The Atlantic City area's population grew 0.8% from 2020 to 2025 (369,221 → 372,047), ranking #264 of 387 metros for growth (typical metro +2.5%). People moving in (net +8,025) account for more than all of the change.
Census Bureau population estimates, July 1 of each year, 2020–2025.
Homes in Atlantic City
The Atlantic City area has about 230,105 homes. 49% were built before 1980 (typical metro 45%), so its housing is older than most; 8% were built in 2010 or later. Older homes often need more repair, replacement and upgrade work. 74% of households own their home, and the median home value is $366,000.
Census American Community Survey, 2024 1-year estimates (table DP04).
New construction
New-home permits in Atlantic City are up 101% from 2021 to 2025 (804 → 1,613).
In 2025 the Atlantic City area approved permits for 1,613 new homes (1,347 single-family), or 4.3 per 1,000 residents, ranking #158 of 393 metros.
Working outdoors in Atlantic City Government data
In an average year, Atlantic City has 23 days at 90°F or hotter (fewer than most metros; typical metro 33), 101 nights below freezing (typical 90) and 75 days with a tenth of an inch of rain or more, and 17 inches of snow. Summer afternoons average 84°F and winter nights 27°F. That matters for sheet metal workers: heat and freezes shape the working season and the hours.
NOAA U.S. Climate Normals, 1991–2020 averages, Atlantic City International Airport, NJ station. Compare cities on outdoor work weather.
Employee vs. working for yourself Your scenario
A model, not a market rate. It shows the break-even rate to match a $100,470 employee salary once you cover what an employer normally pays for (including the employer half of Social Security and Medicare, 7.65%), then adds your profit margin. Change any number.
Break-even rate
With your profit margin
How this calculator works. Weighing a contractor job against a W-2 one? Try the 1099 vs. W-2 comparison. Billable hours are hours you can charge a customer. Driving, quoting, paperwork and slow weeks aren't billable, which is why 1,400 is a common starting point versus 2,080 paid hours as an employee.
Get sheet metal worker pricing & estimate templates →Compare Atlantic City with another city →
Keep exploring
Could this trade pay more somewhere else?
ToolBest cities for sheet metal workersRank every metro on pay, buying power, rent and jobs.Is a job offer here any good?
ToolCheck an offer in Atlantic CitySee where it falls among local sheet metal workers, after the commute.Could you afford to live here?
ToolAtlantic City budgetMonthly take-home, HUD rent and local prices on this pay.About this data
Local to the Atlantic City metro: pay (BLS, May 2025) and pay over time (2020–2025, CPI-adjusted), prices (BEA, 2024), rent (HUD, FY2027), new construction, housing, population and commuting (Census), unemployment (BLS) and business counts (Census, by industry). National: job outlook and training (BLS projections), injury rates (BLS) and duties (O*NET). Jobs are employment estimates, not open positions; grades rank Atlantic City against every other metro for sheet metal workers. Every source, year and formula is on our data page.
Report a data issue on this page
The Census doesn't publish one-person business or competition figures for sheet metal workers as a separate industry, so that section is left out.